Xerox VersaLink B7030 Service Manual

April 2017
2-61
Xerox® VersaLink® B7025/B7030/B7035 Multifunction Printer
012-152A
Status Indicator RAPs
Launch Issue
012-152A Compiler Exit Sensor On Jam RAP
BSD-ON: BSD 12.3 Integrated Office Finisher Transportation
Initial Actions
NOTE: Ensure the correct RAP is performed, refer to the 012-152 Compiler Exit Sensor On
Jam Entry RAP.
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to GP 10. Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check the compiler exit sensor, PL 12.12 Item 16 is correctly installed and free from for-
eign objects and that the actuator is not broken.
• Switch off, then switch on the machine, GP 10.
Procedure
Check the specifications of paper, GP 15. Paper is in specification.
YN
Load paper that is in specification.
Check the condition of the paper. The paper is in normal condition without any problem
that causes the paper to be bent or caught.
YN
Resolve any problem that causes the paper to be bent or caught.
Check the transport path for a foreign object, deformed part, and paper dust. The transport
path is good.
YN
Repair the deformed part(s) and remove the foreign object(s) and paper dust.
Check the exit roll, PL 12.11 Item 10 for wear, deterioration or paper dust. The exit roll is
good.
YN
Remove the paper dust or install a new exit roll, PL 12.11 Item 10.
Check the drive mechanism to the transport roll for a deformed parts, broken parts, and/or belt
damage.
The drive mechanism is good.
YN
Repair defects or damage to the drive mechanism. Install new components as necessary,
PL 12.11.
Check that the finisher is installed correctly. The finisher is correctly installed and correctly
connected to the IOT.
YN
Reinstall the finisher correctly.
Enter dC330 code 012-150. Actuate the compiler exit sensor. The display changes.
YN
Check the connections of P/J8709 and P/J8728. The connectors are good.
YN
Secure the connections.
Check for an open or short circuit between P/J8709 and P/J8728. The wiring is good.
YN
Repair the open or short circuit.
Measure the voltage between the finisher PWB P/J8709 pin 3 (+) and ground (-). The
voltage is approximately +5VDC.
YN
Check the +5VDC circuit. Refer to the Wiring Diagrams.
Measure the voltage between the finisher PWB P/J8709 pin 2 (+) and ground (-). Actuate
the compiler exit sensor.
The voltage changes.
YN
Install a new compiler exit sensor, PL 12.12 Item 16.
Check the wires and connectors for an intermittent open or short circuit. If the fault per-
sists, install a new finisher PWB, PL 12.14 Item 1.
Enter dC330 code 012-095. The finisher transport motor runs.
YN
Check the connections of P/J8706 and P/J8739. The connectors are good.
YN
Secure the connections.
Check for an open or short circuit between P/J8706 and P/J8739. The wiring is good.
YN
Repair the open or short circuit.
Measure the voltage between the finisher PWB P/J8706 pin 5 (+) and ground (-), and P/
J8706 pin 7 (+) and ground (-).
Each voltage is approximately +24VDC.
YN
Check the +24VDC circuit. Refer to the Wiring Diagrams.
Check the wires and connectors for an intermittent open or short circuit. If the fault per-
sists, install a new components as necessary:
• Finisher transport motor, PL 12.11 Item 17.
• Finisher PWB, PL 12.14 Item 1.
Check the wires and connectors for an intermittent open or short circuit. If the fault persists,
install a new finisher PWB, PL 12.14 Item 1.

Xerox VersaLink B7030 Specifications

General

Brand	Xerox
Model	VersaLink B7030
Category	All in One Printer
Language	English