441
Macro Attachment Assigning
Chapter 16 Macros
a) In the case of an event that inserts or deletes a key by an independent key
transition, the key state at the time of event registration (inserted or not
inserted) is also saved in the macro. When the macro is executed, the event
is only replayed if the key state matches the saved state. (Example: For a
macro with an event that deletes a key, when the macro is executed, if the
key is inserted it is deleted, but otherwise nothing occurs as concerns
keying.)
b) KEY5 to KEY8 and DSK5 to DSK8 require an assignment.
c) Assignment is required
• After setting a macro attachment to a cross-point button
of the bus assigned by AUX delegation setting, if in the
Setup menu you change the bus assignment to the
button, the macro attachment setting disappears.
• After setting a macro attachment to a button for which
you can perform function replacement or function
assignment, if you change the function assignment to the
button, the macro attachment setting disappears.
• After setting a macro attachment to a cross-point button
in the cross-point control block, if you change the
function assignment to the button, the macro attachment
setting disappears.
Enabling and disabling macro attachment
You can temporarily disable the macro attachment
settings. When a macro attachment is disabled, pressing
the button does not cause execution of the assigned macro.
You can enable or disable macro attachments for the
individual control panels. Assign the function to enable or
disable macro attachments to a button in the utility/
shotbox control block or a user preference button, and turn
the button on and off as required.
Setting a macro attachment to a fader lever
You can set a macro attachment to any particular position
of a fader lever in the transition control block.
• In macro-only mode it is not possible to set a macro
attachment.
• It is not possible to set a macro attachment to a fader
lever in the keyframe control block or downstream key
control block.
Clearing the macro attachments
You can clear all of the macro attachments in a single
operation.
Displaying the macro attachment list
You can display the macro attachment settings in the form
of a list in the menu display to check them.
Setting and Canceling a Macro
Attachment
Setting a macro attachment to a button
This section describes the example of setting a macro
attachment for the background A row cross-points.
For details, see “Setting a macro attachment to a button”
(page 440) for the buttons for which a macro attachment
can be set.
For each of the [PRE MCRO] and [POST MCRO] settings,
it is necessary to make assignments to user preference
buttons in the menu control block or to the utility/shotbox
control block. Carry out these assignments in the Eng
Setup >Panel >Prefs/Utility menu (see page 506).
1
Recall the macro register (1 to 250) that you want to
assign to the button (see page 431).
2
To make the setting in pre macro mode, hold down the
[PRE MCRO] button assigned to a utility/shotbox
control block button or user preference button. To
make the setting in post macro mode, hold down the
similar [POST MCRO] button, then press the desired
button in the background A row.
The cross-point button you pressed flashes amber, and
the register you recalled in step 1 is assigned to the
button.
If you make both pre macro and post macro
settings for the same button
The later setting is valid.
To set a macro attachment without changing
cross-points
When you set a macro attachment to a cross-point button,
you can make the setting without changing the bus cross-
Downstream key
control block
• [DSK1 ON] to [DSK8 ON] buttons
a) b)
• [KEY1 ON] to [KEY8 ON] buttons
a) c)
• [TAKE] button
a)
• [MIX], [WIPE], [DME], and [CUT]
buttons
Transition control
block
All buttons except [PRIOR SET],
[TRANS PVW], [SHIFT], [ADD],
[KF], [MAIN], [SUB], [LIMIT SET],
[K-SS], and [K-SS STORE] buttons
Utility/shotbox control
block
Memory recall buttons
Menu control block [PREFS 1] to [PREFS 16] buttons
Notes
Notes
Block Button
Notes
To Next Page
Loading...
Need help?
General