Send documentation comments to mdsfeedback-doc@cisco.com
6-129
Cisco MDS 9000 Family Command Reference
OL-8413-07, Cisco MDS SAN-OS Release 3.x
Chapter 6 Debug Commands
debug wwn
debug wwn
To enable debugging for the world wide name (WWN) manager, use the debug wwn command in EXEC
mode. To disable a debug command, use the no form of the command or use the no debug all command
to turn off all debugging.
debug wwn {all | detail | errors | flow | trace}
no debug wwn {all | detail | errors | flow | trace}
Syntax Description
Defaults Disabled.
Command Modes EXEC mode.
Command History
Usage Guidelines None.
Examples The following example displays the system output when the debug wwn all command is issued:
switch# debug wwn all
Apr 29 19:24:17 wwn: 53601-wwnm_sdwrap_dispatch:77
|SDWRAP massage Successfully processed
Apr 29 19:24:17 wwn: Src: 0x00000601/5206 Dst: 0x00000601/46 ID: 0x002C7DE4 Size: 252
[REQ] Opc: 182 (MTS_OPC_DEBUG_WRAP_MSG) RR: 0x002C7DE4 HA_SEQNO: 0x00000000 TS:
0x55D49A130243 REJ:0
Apr 29 19:24:17 wwn: 2F 64 65 76 2F 70 74 73 2F 30 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Apr 29 19:24:17 wwn: 00 00 00 00 00 00 00 00 2E 00 00 00
all Enables all WWN debug options.
detail Enables all WWN output
error Enables debugging for WWN error conditions.
flow Enables flow-level WWN debug options.
trace Enables debugging for WWN traces.
Release Modification
1.0(2) This command was introduced.
To Next Page
Loading...
Need help?
General