Xerox WorkCentre 5225 Service Manual

February, 2008
5-10
WorkCentre 5225, 5230
PL 2.3
Launch Version
Parts List
PL 2.3 Feeder 1/2 Assembly
Item Part Description
1 – Upper Frame (P/O PL 2.1 Item 7)
2 127K38171 Tray 1/2 Feed/Lift Up Motor
3 – Bracket (P/O PL 2.1 Item 7)
4 – Spacer (P/O PL 2.1 Item 7)
5 – Gear (31T) (P/O PL 2.1 Item 7)
6 – Spring (P/O PL 2.1 Item 7)
7 – Oneway Clutch (P/O PL 2.1 Item 7)
8 – Oneway Gear (P/O PL 2.1 Item 7)
9 – Gear (13T) (P/O PL 2.1 Item 7)
10 – Bearing (P/O PL 2.1 Item 7)
11 – Shaft (P/O PL 2.1 Item 7)
12 – Front Chute (P/O PL 2.1 Item 7)
13 120E22481 Actuator
14 930W00113 Tray 1/2 Level Sensor, Tray 1/2 No
Paper Sensor
15 113E37571 Harness Holder
16 962K19692 Wire Harness
17 – Gear (28T/21T) (P/O PL 2.1 Item 7)
18 – Gear (29T) (P/O PL 2.1 Item 7)
19 – Spring (P/O PL 2.1 Item 7)
20 – Feed Roll (P/O PL 2.3 Item 40)
(REP 2.3.1)
21 005K05890 Oneway Clutch
22 005K06760 Oneway Gear (22T)
23 – Shaft (P/O PL 2.1 Item 7)
24 – Chute (P/O PL 2.1 Item 7)
25 – Spring (P/O PL 2.1 Item 7)
26 005K81880 Friction Clutch
27 – Support (P/O PL 2.1 Item 7)
28 – Retard Roll (P/O PL 2.3 Item 40)
(REP 2.3.1)
29 – Spacer (P/O PL 2.1 Item 7)
30 – Gear (33T) (P/O PL 2.1 Item 7)
31 – Support Assembly (P/O PL 2.1 Item
7)
32 – Nudger Roll (P/O PL 2.3 Item 40)
(REP 2.3.1)
33 – Gear (25T) (P/O PL 2.1 Item 7)
34 – Lower Frame (P/O PL 2.1 Item 7)
35 – Bearing (P/O PL 2.1 Item 7)
36 – Gear (34T) (P/O PL 2.1 Item 7)
37 – Lever (P/O PL 2.1 Item 7)
38 – Bearing (P/O PL 2.1 Item 7)
39 – Washer (P/O PL 2.1 Item 7)
40 604K20360 Tray Feed Roller Kit (3/Kit) (REP
2.3.1)

Xerox WorkCentre 5225 Specifications

General

Maximum print size	A3 (297 x 420 mm)
Internal memory	No MB
Type	Digital copier