D-Link DWL-8610AP User Manual

Basic Setup
D-Link Unified Wired and Wireless Access System
Oct. 2015 Page 540
D-Link UWS User Manual
The following table describes the fields available on the Wireless Global Configuration page.
Table 324: Basic Wireless Global Configuration
Field Description
Enable WLAN Switch Select this option to enable WLAN switching functionality on the system. Clear the
option to administratively disable the WLAN switch.
If you clear the option, all peer switches and APs that are associated with this switch
are disassociated.
Disabling the WLAN switch does not affect non-WLAN features on the switch, such
as VLAN or functionality.
Auto IP Assign Mode Select this option to allow the wireless feature to automatically assign itself an IP
address from one of the active interfaces. If this option is cleared, you must manually
assign the IP address in the Switch Static IP Address field.
WLAN Switch
Operational Status
Shows the operational status of the switch. The status can be one of the following
values:
• Enabled
• Enable-Pending
• Disabled
• Disable-Pending
If the status is pending, click Refresh to update the screen with the latest
information.
WLAN Switch
Disable Reason
If the status is disabled, this field is displayed, and one of the following reasons is
listed:
• None: The cause for the disabled status is unknown.
• Administrator disabled: The Enable WLAN Switch check box has been cleared.
• No IP Address: The WLAN interface does not have an IP address.
• No SSL Files: The DWS-4000 Series switch communicates with the APs it manages
by using Secure Sockets Layer (SSL) connections. The first time you power on the
DWS-4000 Series switch, it automatically generates a server certificate that will
be used to set up the SSL connections. The SSL certificate and key generation
typically completes within a few minutes.
If routing is enabled on the switch, the operational status might be disabled due to
one of the following reasons:
• No Loopback Interface: The switch does not have a loopback interface.
• Global Routing Disabled: Even if the routing mode is enabled on the WLAN switch
interface, it must also be enabled globally for the operational status to be
enabled.

D-Link DWL-8610AP Specifications

General

2.4 GHz	Yes
Modulation	-
Frequency band	2.4 - 2.497, 4.9 - 5.85 GHz
Number of users	- user(s)
Channels quantity	- channels
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3ab, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x
Wi-Fi data rate (max)	1750 Mbit/s
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	1000 Mbit/s
Flash memory	64 MB
Internal memory	512 MB
Internal	No
Certification	CE, FCC, IC
Product color	Gray
Ethernet LAN (RJ-45) ports	2
Antennas quantity	6
Antenna gain level (max)	6.5 dBi
Power supply type	PoE, DC
Power consumption (typical)	14 W
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Package depth	265 mm
Package width	238 mm
Package height	112 mm
Package weight	1160 g
Pallet width	1200 mm
Pallet length	1100 mm
Pallet height (air)	1955 mm
Pallet gross weight (air)	385580 g
Quantity per pallet (air)	210 pc(s)
Shipping (inner) case width	280 mm
Shipping (inner) case height	260 mm
Shipping (inner) case length	585 mm
Shipping (inner) case weight	8740 g
Shipping (inner) case net weight	5800 g
Number of cartons per pallet (air)	42 pc(s)
Quantity per shipping (inner) case	5 pc(s)

Weight and Dimensions

Depth	171 mm
Width	198 mm
Height	40 mm
Weight	240 g