D-Link DWL-8610AP User Manual

Configuring Advanced Settings
D-Link Unified Wired and Wireless Access System
Oct. 2015 Page 598
D-Link UWS User Manual
The traps specified in Table 349 below are generated only by the Cluster Controller unless otherwise specified.
Table 349: SNMP Traps
Field Description
AP Failure Traps If you enable this field, the SNMP agent sends a trap if an AP fails to associate or
authenticate with the switch.
AP State Change Traps If you enable this field, the SNMP agent sends a trap for one of the following reasons:
• Managed AP Discovered
• Managed AP Failed
• Managed AP Unknown Protocol Discovered
• Managed AP Load Balancing Utilization Exceeded
Client Failure Traps If you enable this field, the SNMP agent sends a trap if a wireless client fails to
associate or authenticate with an AP that is managed by the switch.
Client State Change
Traps
If you enable this field, the SNMP agent sends a trap for one of the following reasons
associated with the wireless client:
• Client Association Detected
• Client Disassociation Detected
• Client Roam Detected
Peer Switch Traps If you enable this field, the SNMP agent sends a trap for one of the following reasons
associated with a peer switch
• Peer Switch Discovered
• Peer Switch Failed
• Peer Switch Unknown Protocol Discovered
• Configuration command received from peer switch. (The switch need not be
Cluster Controller for generating this trap.)
RF Scan Traps If you enable this field, the SNMP agent sends a trap when the RF scan detects a new
AP, wireless client, or ad-hoc client.
Rogue AP Traps If you enable this field, the SNMP agent sends a trap when the switch discovers a
rogue AP. The agent also sends a trap every Rogue Detected Trap Interval seconds
if any rogue AP continues to be present in the network.
TSPEC Traps If you enable this field, the SNMP agent sends a trap when the following TSPEC-
related events occur:
• An authorized WMM client is repeatedly using more bandwidth than was
allocated for its traffic stream.
• A WMM-enabled client is sending prioritized traffic without authorization to use
admission controlled resources.
WIDS Status Traps If you enable this field, the SNMP agent sends a trap for one of the following reasons:
• This switch has become Cluster Controller
• Rogue Client detected
• Rogue Client(s) continue to exist, after every Rogue Detected Trap Interval
seconds
• Maximum number of Managed APs in the peer group exceeded

D-Link DWL-8610AP Specifications

General

2.4 GHz	Yes
Modulation	-
Frequency band	2.4 - 2.497, 4.9 - 5.85 GHz
Number of users	- user(s)
Channels quantity	- channels
Networking standards	IEEE 802.11a, IEEE 802.11ac, IEEE 802.11b, IEEE 802.11g, IEEE 802.11n, IEEE 802.3, IEEE 802.3ab, IEEE 802.3at, IEEE 802.3u, IEEE 802.3x
Wi-Fi data rate (max)	1750 Mbit/s
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Maximum data transfer rate	1000 Mbit/s
Flash memory	64 MB
Internal memory	512 MB
Internal	No
Certification	CE, FCC, IC
Product color	Gray
Ethernet LAN (RJ-45) ports	2
Antennas quantity	6
Antenna gain level (max)	6.5 dBi
Power supply type	PoE, DC
Power consumption (typical)	14 W
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	10 - 90 %
Package depth	265 mm
Package width	238 mm
Package height	112 mm
Package weight	1160 g
Pallet width	1200 mm
Pallet length	1100 mm
Pallet height (air)	1955 mm
Pallet gross weight (air)	385580 g
Quantity per pallet (air)	210 pc(s)
Shipping (inner) case width	280 mm
Shipping (inner) case height	260 mm
Shipping (inner) case length	585 mm
Shipping (inner) case weight	8740 g
Shipping (inner) case net weight	5800 g
Number of cartons per pallet (air)	42 pc(s)
Quantity per shipping (inner) case	5 pc(s)

Weight and Dimensions

Depth	171 mm
Width	198 mm
Height	40 mm
Weight	240 g